Didn’t get to select L or R side when ordering.
Didn’t get to select L or R side when ordering.
The hose and fittings are nice quality. Their ability to get stuff shipped out quickly dose not happen.
It took a week to get my order to shipping.
Skip to product information
Manufacturer’s Warranty on ferrules/consumables
Fast Shipping • Free $99+
Expert Support
Replacement ferrules for AN PTFE Fittings
$15.00
Reliable shipping
Flexible returns
Replacement Ferrules for Hot Rod AN LLC PTFE Hose End Fittings
Refresh and reuse your PTFE AN hose ends the right way. These precision replacement ferrules (olives) are made specifically for Hot Rod AN LLC PTFE hose and PTFE hose end fittings to restore a perfect seal after disassembly.
What’s included
- 5 × replacement PTFE ferrules (olives) — choose your AN size to match your Hot Rod AN PTFE hose & ends
One ferrule is required per hose end. A 5-pack typically services two hose ends with spares.
Choose your size
| Ferrule Size | Fits | Typical Use |
|---|---|---|
| AN-6 | Hot Rod AN PTFE AN-6 hose & AN-6 PTFE hose ends | Most EFI feed/return lines |
| AN-8 | Hot Rod AN PTFE AN-8 hose & AN-8 PTFE hose ends | High-flow feed, coolers |
| AN-10 | Hot Rod AN PTFE AN-10 hose & AN-10 PTFE hose ends | Oil/trans cooler runs |
Compatibility: Designed for Hot Rod AN LLC PTFE hose & PTFE hose ends. Not guaranteed to fit other brands.
- Exact fit: restores factory-fresh sealing when reusing PTFE hose ends
- Leak-resistant: properly seats on the PTFE liner for a gas-tight seal
- Cost-effective: reuse expensive hose ends—replace only the ferrule
- PTFE-ready: ethanol-compatible and heat-resilient when assembled correctly
Pro install tips:
- Cut back to fresh, undamaged PTFE liner. Wrap the cut area tightly with tape before cutting to control braid fray; remove tape after cutting.
- Slide the nut over the hose, then seat the new ferrule fully on the PTFE liner—no stray braid under the ferrule.
- Clamp the fitting body in aluminum vice jaws; tighten the nut with an aluminum AN wrench until fully seated.
- Pressure-test the line before driving. For EFI, use a 10 micron or finer (≤10 μm) pressure-side filter.
Full walkthrough: PTFE Hose & AN Fittings Install Instructions.
Specs
| Pack size | 5 ferrules (olives) per pack |
| Sizes | AN-6, AN-8, AN-10 (Hot Rod AN PTFE systems) |
| Material | Precision PTFE/metal ferrule set (as required by our hose ends) |
| Use | Reassembly of PTFE AN hose ends to maintain a proper seal |
Recommended add-ons
- PTFE AN hose end fittings (match size to ferrules)
- PTFE hose (by the foot & bundles)
- AN install tools (aluminum AN wrench, vice jaws, cutting shears)
- EFI fuel filters (≤10 μm)
Manufacturer’s Warranty on ferrules/consumables
Fast Shipping • Free $99+
Expert Support
Quick FAQs
Do I need new ferrules when I reuse a PTFE hose end?
Yes. PTFE hose ends require a fresh ferrule each time they’re reassembled for a proper seal.
Will these fit other brands?
They’re sized for Hot Rod AN LLC PTFE hose and PTFE hose ends. Fitment with other brands isn’t guaranteed.
How many should I buy?
Count your hose ends—you’ll need one ferrule per end. A 5-pack typically covers two ends with a spare.